In the Atlant washing machine, a None error was displayed on the scoreboard. What does this mean? Your Atlant washing machine has generated too much foam.
On electromechanical models without a screen, with the DTC None, all 4 indicators light up.
What to do and how to fix the problem, read on.
Note! If you see that the Atlant washing machine shows a None error on the display and the floor is filled with foam, immediately disconnect the AGR from the mains.
The causes of the malfunction
The fact is that an excess of foam can get to the electronic elements or the engine. This increases the likelihood of a short circuit.
Do the following:
- Manually drain the water using a drain filter. On most Atlant washing machines, the filter is located on the front panel at the bottom, behind the hatch. Open the hatch, substitute the container and remove the filter.
- Remove all the laundry from the machine.
- Clean the tank of foam.
- Turn on the rinse. Repeat it until all foam is gone.
- Dry the filter.
- Wipe the control panel thoroughly.
To understand how to correct the situation and remove the None error, you need to understand the causes of the malfunction. Often this happens:
- As a result of using low-quality or non-machine washable powder.
- Due to excessive use of detergents.
- Due to the softness of the water: the softer the water, the better the powder dissolves and foams.
- When washing voluminous and porous linen (curtains, tablecloths, tulle). Just because a drum is clogged with light things to failure does not mean that you need to pour a lot of powder. The washing of this laundry is accompanied by a large formation of foam.
How to fix the situation
How to reset the None error and solve the problem if you poured powder according to the instructions, did not install a filter for cleaning and did not wash porous things? Why then does the Atlant washing machine give an error code?
We will analyze the main causes of the problem.
Rubber cuff has lost tightness
The cuff could leak over time, as a result of which it lost its tightness and began to leak water. Small sharp objects during washing could damage the cuff.
How to check and replace:
- Unplug the Atlant washing machine.
- Bending the cuff, you will see a metal clamp.
- Hooking it with a screwdriver, swirl in a circle and remove the clamp.
- Disconnect the door cuff from the top panel and thread it inside the machine.
- Remove the two screws and remove the top panel of the Atlant washer.
- To remove the internal clamp, unscrew the fastening screw.
- Now remove the cuff from the front.
- Inspect it at the time of damage, install patches or replace the cuff.
The video will help you in your work:
Violation in the drain system
If, after checking the cuff, the None error still remains on the SM Atlant, the entire drainage system must be checked. Signs of its violation are the formation of water and foam under the machine.
For check:
- Inspect the drain hose and its connections to the Atlant and the sewer. Tighten all connections, check hose for damage and cracks, replace if necessary.
- The drain filter is also inspected at the time of leakage.
- The pump is being checked. After you get to the pump, see if there is water under it. Then carefully inspect the pump.
- The drain pipe must be replaced if damaged. But first, let's figure out how to get to it.
How to replace the nozzle from the tank to the pump and remove the None error in the Atlant washer:
- Drain all water from the machine and unplug it.
- Remove the dispensing tray and check the drain filter for residual water.
- Turn off communications.
- Put the Atlant washer on its side, allowing access to the bottom.
- Unclench collars which fasten a branch pipe.
- Disconnect a branch pipe from a tank.
- Unscrew the pressure chamber from connecting to the tank.
- Having disconnected a collar, remove a branch pipe.
- Install the new item in reverse order.
Be careful when choosing a powder for an Atlant washing machine. If the error is no longer displayed on the scoreboard, then everything is done correctly.